Frequently asked questions
How To Regrip a Golf Club
Step 1: Secure the shaft in a vise near the tip of the grip using the protective Rubber Vise Clamp. Position the club face perpendicular to the floor in the playing position.
Step 2: Remove the old grip with a straight blade or stripper. (Use a utility knife with a hook blade on graphite shafts to avoid damage to the shaft.) Be sure to cut away from yourself at all times. Peel or scrape off the old grip and grip tape.
Step 3: Apply the grip tape with 1/4″ over the edge and smooth over the shaft of the club. (Note that the grip tape will not be as long as the grip itself, that is OK)
Step 4:Remove the tape backing and cover the end of the shaft with extra tape pushing it into the end of the shaft.
Step 5: Cover the vent hole in the butt end with your finer or golf tee, spray/pour a generous portion of Grip Solvent inside the new grip. Close the open end of the grip with your hand and shake to cover the entire inside of the grip.
Step 6: Pour the excess Grip Solvent (through the vent hole) over the entire length of the two sided tape. Apply generously.
Step 7: Place the grip over the shaft butt (with alignment pattern up) onto the club by squeezing the open end of the grip. This must be done while the grip is still wet with Grip Solvent. Push the grip entirely onto the club. Be sure the grip butt is against the shaft butt.
Step 8: The grip can now be properly aligned with the pattern square to the club face. (This must happen within a minute or so after applying the grip.)
Step 9: Allow grips to dry a few hours before playing.
To regrip a golf club, you need the following items:
- New Golf Grips
- Grip Solvent
- Grip Tape
- Hook Blade
- Bench Vise and Vise Clamp (Not needed, but makes the process a lot easier)
Shop Bundles and save 10% (Includes everything above except Bench Vise)
If the top of the grip is aligned with the leading edge of the club face, then the grip is aligned correctly.
Regrip Supplies
We offer 7 different types of grip kits. Here is what comes in each one:
Light Kit: 5oz grip solvent and 15 tape strips
Deluxe Kit: 5oz grip solvent, 15 tape strips, hook blade, and rubber vise clamp
Premium Kit: 5oz grip solvent, 15 tape strips, hook blade, rubber vise clamp, and grip tape remover
Ultimate Kit: 8oz grip solvent, 30 tape strips, hook blade, and rubber vise clamp
Elite: 8oz grip solvent, 30 tape strips, hook blade, rubber vise clamp, and grip tape remover
Tape Roll Kit: 32oz solvent, 18 yard tape roll, hook blade, rubber vise clamp, and grip tape remover
All in One Kit: 5oz grip solvent, 15 tape strips, hook blade, rubber vise clamp, grip tape remover, and bench vise
If it is your first time regripping and you don't have a bench vise, the All in One Kit is the one for you. If you have a bench vise, go with the Premium Kit. If it's not your first time regripping and you only need the tape and solvent, the Light Kit is the one for you.
If you are regripping just 1 set of clubs, I would recommend using tape strips, as they are easier to use. If you are a club builder, I would recommend using a tape roll as it is less expensive.
You can regrip up to 64 clubs with an 18 yard tape roll (up to 128 for 36 yard roll)
Our grip tape remover works extremely well when removing tape from a steel shaft. For best results, heat the tape up using a hair dryer or heat gun prior to using the grip tape remover tool. Alternatively, you can use a utility knife or hook blade and cut the tape and then peel it off.
Tape will dry enough to play 2 hours after regripping the club
Yes, you can use a paint tray or something similar to catch excess solvent to use for future projects
2” x 10”
6.7mil thick